16.5 Briggs in a MTD motor runs fast
I just got a MTD Yard Machine 42"cut I think its a 1999 I did a short test drive when I bought it it was ok I got it home started fine but it motor started racing I checked and the choke was stuck so I...
View ArticleClik here to view.
Need help fixing up RP21600 Big Six Ninja
Starting cleaning up and getting my Big Six up to snuff. I took off shroud and gas tank to clean them up. Have two things I can use your advice with: I see two carbs listed. One is auto choke. I assume...
View ArticleMissing magnet.
My engine flywheel has been clicking so I took the flywheel off and noticed a magnet was broken in half and off the flywheel. Will that missing magnet damage the alternator. It's off the alternator not...
View ArticleZ425 Hard starting
I have a Z425 that got to wear it was hard to start like the battery was week so I put a new in and it still wont spin over. I took my hands and spun the flywheel over once and it fired right up and...
View Article30" Walk behind.
Are any of you guys using one of the 30" walk behind mowers? We are going to need something like that very soon. We have been putting it off but it is getting to be obvious it has to happen soon.
View ArticlePlease help. Carb issues??
Hello All, I recently bought an mtd yard machines mower with a 18.5 horse intek single cylinder engine with a nikki carb. it was leaking gas into the intake and leaked if you shut it off. I took the...
View ArticleSnapper 9300D push mower--date of manufacture?
Curious if anyone out there can identify a snapper push lawn mower, model 9300D, serial is 23107948, has a label that says McDonough Power equipment. Thanks! Appears to have a 3hp briggs and a 19" cut.
View Articletroy-bilt front wheel drive self prop walk behind model 12avb25s011
I need to change my drive belt, got it off with no problem but to put it on, I need to take the front cover off to see trans pulley. I can't seem to figure out how that front cover comes off
View Articlecub cadet
my cub cadet model 1515 will not crank over. The starter relay clicks but starter will not engage. It quit on me while I was mowing and would not start.
View ArticleClik here to view.
Rusty Lawn Mower
Hi, trying to buy my first mower and I have an offer for a used one. It's a "Cub Cadet - 173cc/6.75 ft-lbs" It's been stored for about 2 years (hasnt been used since) and has some rust underneath and...
View ArticleHigher Ethanol Blends Can Damage Your STIHL Equipment
STIHL equipment was designed to run on fuel containing no more than 10 percent ethanol. The same fuel you put in your car may not be the same fuel meant for your chain saw, trimmer, blower, or other...
View ArticleClik here to view.
seeking help on a craftsman push mower
I have a craftsman push mower with the rear drive running from a belt. I replaced the drive unit and cannot determine where the spring connects to. Obviously I can't run the machine without it being...
View Articlesounds rough when I engage blades
I inherited an old John Deere 111 I have been working on. Whenever I engage blades it sounds really rough. I don't see a way to adjust the belts, nor any fittings to grease. I looked up the belt #'s...
View ArticleAdvice Needed - Buying ZT for ~1 acre
Hello, Yard I live on 1.17 acres. In the middle of that is a 2700 sq/foot house with a deck and a long driveway. At any rate there is, to me at least, a good size yard to mow. Most of the yard has many...
View ArticleCollege Slashes Cutting Time by Almost Half With New Toro Groundsmaster Rotaries
Two Toro® Groundsmaster® rotary mowers brought in by head groundsman Ian Osbon have reduced cutting time by almost half. Read this article on LawnWorld
View ArticleUnprepared Dad
Greetings Y'all from Southwest Mississippi ! I'm a new member, but have been " lurking" for some time as I researched ZTRs for my next purchase. The level of knowledge and helpfulness on this forum is...
View ArticleCan I deep soak B&S carb at home?
Going to rebuild/clean my B&S 12h802-1531-21 carb. Is there something I can soak carb in overnight (or couple days) at home or does it take industrial strength cleaner to really get into all nooks...
View ArticleShould I paint my replacement deck pulleys?
So I am replacing a few old deck pulleys on my zero turn. The new old ones were painted... not sure if the previous owner painted them or if that was factory. The new ones came unpainted. Should I...
View ArticleNovice needs help!
I just bought a used snapper 1433 and it was doing great when the engine suddenly cut out. The oil looks low and I would like to put some oil in it, but can't figure out how. I don't have a manual....
View ArticleWidth of Z121S with grass catcher?
How wide is the 48" Z121S with the grass catcher chute attached? I am looking to buy and want to make sure it would fit in my shed which has a 60" opening. thanks!
View Article