Two year saga of suspected fuel-starvation issue on Cub HDS 2135, Kohler 12hp...
Hi everyone, For the past 2 years, I've been dealing with what appears to be a fairly common problem with Cub Cadet tractors approaching 500 run hours. They run great for about an hour until the engine...
View ArticleDrivers...
It never seizes to amaze me seeing a pickup truck pulling lawn equipment driving like they're Mario Andretti or something. Almost every time I see a lawn care business truck, the guy driving seems like...
View ArticleWalk behind JD 14SB Blade Brake Clutch Control Repair
I bought my 14SB in 1992 and it's been a great mower. I snagged the blade control cable on a fence and pulled it out of the plastic housing. When I took the housing apart the large spring fell out. I...
View Articlegot another one
picked up a lawnboy m series last nite its in great condition had to drive 180 miles round trip but it was worth it to me anyway.its a non self propelled premix type the model no. is mz21rp18 and I...
View Articleeastlam2
my 455 john deere keeps draining battery. there is a constant draw which seems to be coming from the glow plug mod , is there a relay between this and the glow plug or just replace the whole module?
View ArticleTransaxle problem-mower barely moves and then stops altogether.
I have a Craftsman GTV 16 garden tractor with Varidrive. 16 hp, I believe it's an early 80's model. There is a model and SN plate on the front frame (917-254 050), another one on the rear frame...
View ArticleHow to adjust the "parking brake" on my DYT4000
My DYT4000 tends to roll on hills, even with the "parking brake" set. How can I tighten that up? Keith
View ArticleDrain Plug G2000
Hello, first time flushing a G2000, I was successful in draining the radiator from the bottom valve of it, the cock valve on the L side does not have any water coming form it, is this normal? is there...
View ArticleKohler SV590 Smokes
I have a Kohler SV590 in my Cub Cadet. After it runs for about 10 minutes, it starts to sputter and exhausts blueish smoke. I pulled the air cleaner and it had oil in the area and getting sucked (I...
View ArticleWalk behind Setting The Height on my Honda
I would like to know what notch to set my Honda Lawnmower for 3 inches? Right now I have it in the 5TH notch so what does that equal in inches?
View ArticleCub Cadet zforce44
I have a Cub Cadet zforce 44. I need to replace the transaxle filter. Any advice on removing the old one, it does not thread on or off.
View ArticleEngine Engine revs up and down after needle valve replacement-Snapper SX825
After replacing my needle valve(grafite tip) the motor wants to rev up and down. Before replacement the motor would only throttle about 30%. I am probably getting full throttle now except for the...
View ArticleRepairs Snapper Severe Vibration
Hello all: I just purchased a Snapper front engine rider, Model: LT115D411B, Ser. 25425177, I got the engine running and taking it for a test run, but when the tractor starts moving you feel this...
View ArticleBriggs and Stratton Motor wiring.
I have a Briggs 28N707 1131 E1 motor. 14.5 HP. its in a Toro 71215. last year the poston rod broke and i decided to tackle the job of replacing it and do a major motor cleanup. the motor is completely...
View Articlerider for my daughter
My daughter cuts her own grass with an older Snapper Hivac rider. The old snapper is getting to the point where it needs some serious reconditioning or simply sell it. (tires, belt, dust boots on axle,...
View ArticleHello from Aberdeen, Maryland
Here to look up some information on my walboro WT668 from my rc car
View ArticleHow to keep your discharge chute in up position
So a week or so I bought at Kubota Z121S 48". The Exmark that I sold had a solid metal discharge chute and this had a heavy duty plastic type. The Exmark could be flipped up and it would stay in the up...
View ArticleNeed ID
Has anyone on here hear of a murray rider with a 206cc 5hp engine made from briggs & Stratton? I am buying one but they said it starts but does not drive. Any ideas on this too?:confused2:
View Article