Clik here to view.
Farmers' Almanac
2014-USFA-Winter.jpg Take a look at the Farmers' Almanac for this Winter. Looks like everybody here in the Midwest with me better be prepared for a cold, snowy season. Get your snow blowers ready...
View ArticleShrinking bags
My 1320 bags seem to be getting smaller over the years. Anyone notice that on theirs? Are the bags the same for the twin bag model as the 3-bag model? It takes seconds to fill the bags with leaves,...
View ArticleRepair
1990 toro wheelhorse , will not go into gear , it grinds but will not pop in , can this be adjusted ?416-8
View ArticleAriens ZTR snow plow
I'm looking into getting a snow plow for my 34" Ariens ZTR. I don't want to spend a ton of cash. Any suggestions? Thanks
View ArticleStarting Problem
I'm hoping for a... most likely cause I guess. Got an older Murray Lawn Tractor this summer. 20hp B&S twin. It runs terrific but has a problem when turning over to start. It acts like the timing is...
View ArticleClik here to view.
I think I got scammed...
I just traded for a Craftsman YT4500. It is a 2012 model. I have not been able to keep the drive belt on. After inspection it looks like it has been broken then he tried to repair. I am new at this and...
View ArticleSomebody buy my Mower!
You need the mower and I need the money :thumbsup: This is a commercial ZTR - not a homeowner grade. Very nice and well maintained Hustler Mini Z mower. 560hrs. oil changed regularly (50 - 80 hrs)...
View ArticleClik here to view.
Price Check Old Briggs and Stratton G series
Hey guys Sorry if this is the wrong place to post. I was wondering if someone could give me any info on this old mower I picked up today. It says G series and has Magnetron on the top. I paid $15 for...
View ArticleClik here to view.
Price Check Old Briggs and Stratton G series
Hey guys Sorry if this is the wrong place to post. I was wondering if someone could give me any info on this old mower I picked up today. It says G series and has Magnetron on the top. I paid $15 for...
View Articlejoe5443
I have a 17hp Briggs that will start sometime but other times will not turn over . Put new starter on it and machine did the same thing.
View ArticleNew member
Hi everybody, new to the forum. I own a JD LX280 and I'm looking for info/suggestions on a weather enclosure for snow blowing. I have a soft 3 sided enclosure now but I want a better one.Can I modify...
View ArticleRepairs JD sx95 Starts and runs,quits when put into gear
Have checked all switches and they are ok.Any chance it could be the John Deere Relay - AT75769?I'm really not sure what the relay does.Starts fine and runs well,when I try to shift into gear it kills...
View ArticleClik here to view.
Spindle bearings
image-1233541832.jpg I have always wanted to know why they use sealed bearing in blade spindles and not a two piece roller bearing. So here is my test. Putting bearing and a race in a mtd housing with...
View Articlewiring diagram dyt4000
i would like to get the wiring diagram for the dyt4000 craftsman mower. what i want to do is eliminate the seat switch so it will not stop when off the seat. yep that is a safety thing but i'm tired of...
View ArticleRepairs MTD/YARD MAN/YARD MACHINES/BOLENS/WHITE OUTDOOR MANUALS
Professional Shop Technical Service & Repair Manuals http://manuals.mtdproducts.com/mtd/Public.do
View ArticleDixon vs ?
I've never had a ztr, but I'm going to purchase one by next cutting season. I've looked at the Hustler Fastrack, Scag, Xmark, and yesterday I looked at the Dixon DX152. To my inexperienced eye it...
View ArticleCub Cadet RZT 42 Starting Problem.
When I turn the key the engine will spin about one half revolution then stop. When I turn the key again it does the same thing again. If it actually spins the engine for a full revolution (a rare...
View ArticleStihl 028AV super..suspect clutch slipping
Use the saw weekly, recently, saw revved up fine but bogged down when blade put to a log. Adjusted the idle/high + LA screws but no change (put screws back to original settings), Opened up the case and...
View ArticleD-400 series engine muffler gasket and plate question.
I have a Model 7084, with a D-400 type engine, bricktop. In looking at the parts diagrams on the Lawnboy parts website it appears that there is a sort of shield plate that is a separate part that goes...
View Article