cub cadet LT2042
Hello. My 2006 LT2042 Cub has developed a problem. The rear wheels/hubs have begun to "pop" and wobble while moving the wheel vertically. Meaning, grab the wheel at top and bottom and push in/out on...
View ArticleClik here to view.
Removing front tire
So I've been trying to get our front tire off but it's stuck. I got the snap ring off and I didn't see a washer. But it still won't come off. I know it's gonna be a simple solution, at least I hope,...
View ArticleStihl FS45 string trimmer bump knob - cannot remove
I have a Stihl FS 45 string trimmer with a bump knob I cannot remove. I have used opposing pipe wrenches and it will not twist off. What has happened and better yet what do I have to do to get it off?
View Articleford lawn tractor model LGT 145
I think a bearing is going out on my PTO clutch. Can I have the bearing replaced or does it call for another PTO Clutch??? Thanks, Leon
View ArticleDrive belt replacement / owners manual
Hi all! I have a Murray 38608x12c rider and I've been looking on line for an owners manual. Any suggestions? My drive belt broke and for the life of me I can't figure out how to install a new one. It...
View Articlerepower GT275 engine 17hp kawasaki
Has anyone had to replace the 17hp Kawasaki engine in their GT275? I need a new engine and want to know if there is an workable rebuild or new engine that will slip in as a replacement.
View ArticleClik here to view.
White Outdoor LT542G Bagger?
Hi there, I was giving a used LT542G that seems to be running strong. Judging by the label (see photo) I assume its made by MTD? I was wondering if I can buy a bagging attachment for this unit? If so,...
View Articlestop and start
my husquvana zero turn cranks and runs fine, my problem is that the blade stops turning spind's for a little while then stops again. what could be wrong.
View ArticleClik here to view.
How do I get rid of this weed?
This weed is relentless. Tried stripping all area and reseeding grass. Any chemical that may do the trick now that is summer and full-grown? Any idea appreciated! Attached Images Image 1.jpg (335.7 KB)
View Articlewheel horse 600 series
I got wheel horse 600 series z turn with 42 in deck can i put 48 in deck on
View ArticleFS 66 trimmer problem
I have a worn solid shaft and shaft tube bearings in my FS 66, which causes a terrible vibration and noise at cutting speeds. Replacement parts are unavailable, although I did find something used on...
View ArticleProblem greasing Toro C3000 zero turn
The Toro C3000 is about 2 years old and has just reached the 100 hour mark. There are 2 places where I cannot get any grease into the zerks. The idler arm assembly and the pulley towards the rear,...
View ArticleExtra Set of Scalp Wheels for my JD D125
I am sure most of you know that all of the JD "D" series mowers with 42" decks only have 2 scalp wheels. I was wondering if any of you have every tried to install a second set of aftermarket wheels...
View ArticleClik here to view.
Why Crankshafts Bend...
When considering why a lawn mower crankshaft bends, it's first helpful to consider how much energy actually exists in the rotating blades. A 21-inch lawn mower blade tip moves at nearly 200 miles per...
View ArticleBlades 48 Inch Zero Turn - Mulching/Striping Kit Dilemma
Hi Guys - Trying to get educated on mulching and striping kits for my 48 inch Zero Turn. I am being told mixed messages from multiple dealers. 1. I want to buy a mulching kit but not sure what to get....
View ArticleEthanol in standard Gasoline
I have been a master mechanic since 1970 and am certified in all areas of Automotive and Heavy Diesel Vehicles too. There is a problem with ethanol blended fuels and present or older lawn equipment. 1....
View ArticleRepairs Older Ferris owners be prepaired
I own a seven year old (bought new) FERRIS 3100z 60in deck. 265 hrs. I had a motion dampner fail on the left side( the shock for the left handle) I went to the dealer with the old one in hand and was...
View ArticleGravely ZT HD 52 or Pro Turn 52
Hi, I'm a home owner who cuts about 5 acres. I'm looking to buy either the ZT HD 52" or the Pro Turn 52"? The price is only about $700 difference at my local dealer. I know there are a few differences,...
View ArticlePoulan Pro Trimmer Help...
Hey folks, this is my first post and hopefully someone can help me out. I am 34 and not very familiar with engine repair of any kind. However, I am very mechanically inclined and can pretty much...
View Article